• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Do a Door window lock replacement Change

Change of the door lock is a simple and affordable method to boost your home's security. This isn't for all. It requires some expertise and perseverance.

You need to replace the cylinder, which is located inside the knob's body. The cylinder is what recognizes the key when it is inserted into the lock.

Remove the old lock

The first step in replacing a door lock is to take out the old lock. It's a simple process, but you must keep some things in your mind. Make sure that the new lock is compatible with your door. This will ensure that it fits snugly and does not leave a gap around the latch or deadbolt plug.

After removing the latch plate, you will have to look for two bolts or screws in the casing's interior that hold the casing in place with the two halves of the lock. Remove these screws using a screwdriver and then pull the lock off the door. If you are using a mortise locking system there is an anchor screw that connects the handle to the spindle. Remove the doorknobs by unscrewing this screw using a screwdriver.

It is also recommended to take the deadbolt and latch plug from the hole in the door jamb. Then, you can put in your new lock. If you're replacing a mortise you should take a measurement of the distance between your lock case and the door edge to make sure that the new lock will fit.

It is possible to replace your lock for a variety of reasons, such as the possibility that someone else holds the key or you've got a new roommate. In any event, you could save money by taking the lock off yourself, rather than hiring a professional to do it. It's much simpler than people think and can be completed in just a few moments.

Remove the handle and trim of your door. With a flat screwdriver, take off the trim. You will be able twist off the majority of it and in certain cases the handles could come off completely. Next, examine the handle for a tiny hole on the inside. Then insert a straightened paper clip into it. This will trigger the release mechanism, allowing you to take off the handle. The next step is to look at the inside of the lock for another small tab that you can press using a flat screwdriver. After the spindle has been removed, you can take off the housing and the cylinder.

The process of selecting a new lock

When it comes time to pick a new lock you have a variety of choices. Take a look at various types of locks, and select one that fits the style of your door. Think about the backset which is the distance between the edge and the center of the hole in the lock. Also, think about the cross bore, a small hole in the middle of your door's frame. Also, be sure to choose a lock that will be able to fit the door's thickness and swing.

The American National Standards Institute and BHMA have graded most door locks to give you an idea of their longevity and how difficult it is to pick them up or disable them. A lock grade 3 might be perfect for a quiet apartment in the countryside, whereas a lock of grade 1 may be more suitable for an area with a lot of traffic, such as an open-air storefront.

Most smart door locks require digital code to open. If you're concerned about hacking or other security issues seek out an expert locksmith or your local police department for advice.

Replacing the cylinder

If your door lock's cylinder is damaged or broken you can repair it in just a few minutes by completing a do-it-yourself project. It is important to select the appropriate cylinder and follow all instructions. The first step is to take off the handle or knob if there is one and then remove the trim that is attached to the base of the lock cylinder using a screwdriver. Once the trim has been removed, you will be able to access the screws that keep the cylinder in place and remove them using the flat-head screwdriver. The cylinder can then be gently removed from the door.

Before you install the new cylinder, make sure that it's the right length for the door you are using. Find the distance from the center to the right and left sides of the cylinder with an instrument. Then, purchase an additional cylinder using the same measurements. This will stop cylinders from snapping when doors are kicked or the key gets stuck inside.

Insert the replacement cylinder in the door, and then turn the key. This will align the cylinder with your carrier which is located usually on the outside of your lock. After that, you can loosen the set screw, which is supposed to be a couple of turns in the head. Also, you will need to loosen the screw in the edge of the door that fastens the case, in the event that there is one.

You can replace the cylinder that was used to lock your old lock with the new one by sliding it into the case and tightening the set screws. Reinstalling the piece that connects the cylinder to the stem of a lock indicator is also essential. It is done by pulling three tabs at the back of the cylindrical using needle-nosed pliers. Attach the smaller bracket to the back of the cylinder. Then, you should install the strike plate and latch plate, as well as the retaining ring attached to the top of the lock the cylinder.

Installing the new lock

Start by measuring the door's width if you are replacing a lock that is already in use. Most locksets for residential use are designed for a door thickness of 1 3/8 - 3/4 inch. If your door is thicker, you will need a door kit that is thick and includes longer screws as well as a longer tail piece (for door knobs) or spindle extension (for deadbolts).

Most double glazing window locks repairs come with a detailed instruction booklet to guide you through the installation of the new hardware. Read the instructions carefully before starting the process to make sure that you are following all the steps. The booklet will also provide you with an idea of the level of skill required to complete the task. If you're changing a lock for the first time, you may consider asking a more experienced person for help.

Before installing the new lock, it's recommended to cover the openings with tape the old hardware. This will prevent the screws from slipping through the holes and will also protect any tiles you may have installed. It will also prevent any potential damage from rust dirt, and grime. SECURAM Touch comes with a strip of painter's tape that is intended to be used for this purpose, however you can also use gaffer's tape as well as masking tape if you have it available.

Once you've removed the screws that hold the inside of the lock section to the outside side immediately, pull it back. It's important to do this swiftly to avoid the lock from accidentally closing itself and damage the mechanism.

If the new lock comes with an latch bolt, install the new bolt into the upper cross bore. Make sure you put it in the right location, which is indicated by an arrow. Then, you can screw the latch plate onto the bolt.

Finally, screw the deadbolt and strike plates to the door jamb. Test the deadbolt by throwing it a few times to verify that it is extended all the way into the strike plate and is completely secured. If you're using an electronic smart lock, be sure to follow the instructions to program it. This involves downloading an application, registering your e-mail address, verifying you identity, window door lock repair and door lock repair - Highly recommended Reading, connecting to the wireless network in order to add your device.