• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

How to Replace Door Locks

Your first protection is your door lock. It will prevent unauthorized access to your home. The signs of wear and tear as well as instances like moving into a new residence or burglaries, could trigger the necessity of replacing upvc door lock mechanism your lock.

You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw. This measurement will help you select the appropriate lock.

Deadbolt

If you want to make sure your door is secure from criminals, it's a great idea to install deadbolts. When the bolt is extended into the strike plate of the doorframe it makes it much more difficult for an intruder to get through the door. A single-cylinder deadbolt is activated using a key on the outside and the thumb-turn mechanism that is located inside. Deadbolts can only function only if it is correctly installed.

The first step is to determine if the door has a hole for deadbolts, or if it needs to be bored out. Mark the position of the hole for the deadbolt on the surface of the door by using the template supplied with the lock installation set. Use a tape measure to determine the height of the deadbolt. Mark this high point on the door's edge, and then use a speedsquare to draw a straight line across the mark you made to mark the bolt hole.

Next, use a power drill to bore out this area until the hole is on the other side of the door. This may take some time. Then, sand down the hole and the edges of the door so that it's smooth. It's also an excellent idea to stain or paint the door at this point.

Remove any visible screws from the deadbolt. This will reveal the front and back assemblies of the deadbolt, as well as the internal bolt. Then, loosen the bolt and replace it with a new one that matches your door hardware. The bolt is often connected to a setplate, which you will need to unscrew. Then, you'll need to chisel the area on the door frame for the strike plate.

If your strike plate is not in alignment, it could be because the previous installer did not mortise it properly or that an installation of a weatherstripping altered the strike position. It is necessary to re-mortise the strike plate and possibly even the deadbolt itself to correct this problem. After this is done check the deadbolt by closing and locking it. Make sure the bolt is extending into the strike plate then test the key to ensure it is able to open and close easily.

Knob

When a door knob wears out, it can make your business or home less secure. It can also make opening and closing the door more difficult, which is why it's an ideal idea to Replace Door Lock it. It shouldn't take more than 30 minutes. Use a screwdriver or pliers to take off any knobs or handles. Be careful not to harm other components of the door.

Before starting you'll need to spray WD-40 or a different dry lubricant onto the mechanism of the knob on your door. This will assist the new lock move smoothly when you turn it. It's essential to select the best knob and handle that matches your current doors to ensure proper operation. If you don't already have a matching doorknob, you will need to buy a replacement patio door lock.

To begin the replacement process, look over the knob or handle to find what screws are holding it in place. If there aren't any screws you can use a screwdriver to insert between the cover plate and the plate with hidden screws and then remove it.

After removing the old knob examine it for indications of damage and rust. If the knob is damaged or has marks or scratches, you'll have clean it. Otherwise, it shouldn't require any major work.

Install the new knob. You must first study the two knobs to ensure that you are choosing the appropriate one for your door. You should select one that has an extending rod that's designed to lock into the rod mechanism on the second knob. After you've inserted the new knob into the hole, slide it into the latch.

Test the spring by pressing down on it repeatedly. The latch should pop up each time. Next, install the other new knob and interlock it to the rod mechanism on the first knob. Thread in the other long screws from the interior knob through the hole for the cylinder on the doorknob outside and secure it.

Latch

A latch is a steel piece that extends out into the doorjamb to keep it shut. It is operated by a knob or handle on the inside of the door or a thumb turn on the exterior side of the door. A deadbolt is a device used to secure a latch and stop intrusions from breaking through the glass of the door. It also helps protect against the accidental or deliberate closing by animals or children. The latch can be fitted using a single cylinder deadbolt or double cylinder deadbolts depending on the security level you prefer.

Installing a latch follows the same steps similar to installing a deadbolt but there are a few distinctions. First, measure the setback of the doorjamb with an instrument to make sure that the new lock will fit. The setback is measured from the edge of doorjamb up to the center of hole for the latch plate. Standard setbacks are 2 3/8 to 2. 3/4 inches. If your setback is larger it is possible to purchase an extra-long latch from a locksmith or hardware store.

Then, drill a hole for the latch plate at the doorjamb's edge. Use a chisel and chisel the latch mortise. Make sure the depth is sufficient for the faceplate to be flush with the doorjamb. Place the strikeplate on the floor to ensure it's placed correctly.

If the strike is too high, you can kick the door in or apply pressure using the tire iron or crowbar. This could also cause cracks in the doorjamb. This can be fixed by drilling a new hole into the doorjamb, then removing the core from the hole that was previously made.

Installing the new strike plate is the final step. This can be accomplished by screwing the new plate over the screw holes that are already in place. Then you can use wood putty to fill in the old screw holes and the bolt hole that won't be used. After the putty has dried, sand it to an even finish.

Strike

An electric strike is a metal piece where the latch and deadbolt engage when the door is shut. It is an essential part of the lock's security because it stops the door from opening and provides an additional level of resistance to force or kick. If a door is fitted with an electronic strike, it can be opened by using a key and the control unit that regulates the electrical impulses.

In the past, installing an electronic strike required cutting a portion of a doorjamb in order to remove the latchbolt on a cylindrical lock from the pocket inside the strike. This modification can be an inconvenience in regards to the aesthetics of an opening, and it also exposes the latchbolt and keeper mechanism to any unauthorised users.

Recently, several electric strike manufacturers have created a new type of electric strike called the "No Cut" strike that doesn't require an opening in the doorjamb for operation. The strikes use a unique design that allows the latchbolt and keeper to slide into the strike pocket without damaging the doorjamb faceplate.

The strike is equipped with an internal ramp that raises the keeper and latchbolt when it receives an electrical signal from a controller or reader. The retraction of the keeper and latchbolt causes them to rise on the ramp, locking the door. When the door is shut the deadbolt remains extended and the latchbolt is retracted into the keeper.

Installing an electric strike can be a simple process, especially in the case of replacing upvc door lock and handle the strike on a previous door. However, if you are upgrading to an electric strike in an access control system, you'll be required to ensure that the new system is compatible with the model of lock you've chosen to install. Also, you must make sure that the strike is properly wired to your access control system and is designed to operate in a fail-safe manner.

One way to protect against unauthorized access is to upgrade the strike on your doors to a heavy-duty strike plate. The plates utilize four to six screws of three inches instead of the two three-fourth inch screws typically used in regular strikes. These screws are longer, making it difficult for people to break the frame and reach inside to turn the thumb turn piece of a single cylinder deadbolt.